Search for: All records

Multiple silicon solar cell technologies have surpassed or are close to surpassing 26% efficiency. Dielectric and amorphous silicon-based passivation layers combined with minimal metal/silicon contact areas were responsible for reducing the surface saturation current density below 3 fA cm −2 . At open-circuit, in passivated contact solar cells, the recombination is mainly from fundamental mechanisms (Auger and radiative) representing over 3/4 of the total recombination. At the maximum power point, the fundamental recombination fraction can drop to half, as surface and bulk Shockley–Read–Hall step in. As a result, to further increase the performance at the operating point, it is paramount to reduce the bulk dependence and secure proper surface passivation. Bulk recombination can be mitigated either by reducing bulk defect density or by reducing the wafer thickness. We demonstrate that for commercially-viable solar-grade silicon, thinner wafers and surface saturation current densities below 1 fA cm −2 , are required to significantly increase the practical efficiency limit of solar cells up to 0.6% absolute. For a high-quality n-type bulk silicon minority-carrier lifetime of 10 ms, the optimum wafer thickness range is 40–60 μm, a very different value from 110 μm previously calculated assuming undoped substrates and solely Auger and radiative recombination. In this thickness range surface saturation current densities near 0.1 fA cm −2 are required to narrow the gap towards the fundamental efficiency limit. We experimentally demonstrate surface saturation currents below 0.5 fA cm −2 on pi/CZ/in structures across different wafer thicknesses (35–170 μm), with potential to reach open-circuit voltages close to 770 mV and bandgap-voltage offsets near 350 mV. Finally, we use the bandgap-voltage offset as a metric to compare the quality of champion experimental solar cells in the literature, for the most commercially-relevant photovoltaic cell absorbers and architectures. 

Fluorocarbons have been shown experimentally by Baker and coworkers to combine with the cyclopentadienylcobalt (CpCo) moiety to form fluoroolefin and fluorocarbene complexes as well as fluorinated cobaltacyclic rings. In this connection density functional theory (DFT) studies on the cyclopentadienylcobalt fluorocarbon complexes CpCo(L)(C n F 2n ) (L = CO, PMe 3 ; n = 3 and 4) indicate structures with perfluoroolefin ligands to be the lowest energy structures followed by perfluorometallacycle structures and finally by structures with perfluorocarbene ligands. Thus, for the CpCo(L)(C 3 F 6 ) (L = CO, PMe 3 ) complexes, the perfluoropropene structure has the lowest energy, followed by the perfluorocobaltacyclobutane structure and the perfluoroisopropylidene structure less stable by 8 to 11 kcal mol −1 , and the highest energy perfluoropropylidene structure less stable by more than 12 kcal mol −1 . For the two metal carbene structures Cp(L)CoC(CF 3 ) 2 and Cp(L)CoCF(C 2 F 5 ), the former is more stable than the latter, even though the latter has Fischer carbene character. For the CpCo(L)(C 4 F 8 ) (L = CO, PMe 3 ) complexes, the perfluoroolefin complex structures have the lowest energies, followed by the perfluorometallacycle structures at 10 to 20 kcal mol −1 , and the structures with perfluorocarbene ligands at yet higher energies more than 20 kcal mol −1 above the lowest energy structure. This is consistent with the experimentally observed isomerization of the perfluorinated cobaltacyclobutane complexes CpCo(PPh 2 Me)(–CFR–CF 2 –CF 2 –) (R = F, CF 3 ) to the perfluoroolefin complexes CpCo(PPh 2 Me)(RCFCF 2 ) in the presence of catalytic quantities of HN(SO 2 CF 3 ) 2 . Further refinement of the relative energies by the state-of-the-art DLPNO-CCSD(T) method gives results essentially consistent with the DFT results summarized above. 

Cadmium telluride and silicon are among the widely used absorber materials in photovoltaic industry. A tandem solar cell of these two can absorb significant portion of solar spectrum to yield high efficiency due to the added voltage of the two solar cells. On basis of low-cost production, a CdTe/Si cell has the potential to produce low-cost and high efficiency tandem PV. The CdTe top cell in a substrate configuration is essential to achieve a tandem between CdTe and Si. A functional CdS/CdTe solar cell in the substrate configuration was fabricated on a Si wafer. Current -Voltage measurements show a diode-like curve with lower J-V parameters compared to standard CdS/CdTe cells. SCAPS simulations were performed to identify possible reasons for poor performance and help improve the device performance. 

The known sandwich compound [η 5 -(CH 2 ) 3 N 2 (BPh) 2 CMe] 2 Fe in which adjacent C 2 units are replaced by isoelectronic BN units can be considered as a boraza analogues of ferrocene similar to borazine, B 3 N 3 H 6 , considered as a boraza analogue of benzene. In this connection, the related bis(1,2,3,5-tetramethyl-1,2-diaza-3,5-diborolyl) derivatives (Me 4 B 2 N 2 CH) 2 M (M = Ti, V, Cr, Mn, Fe, Co, Ni) for all of the first row transition metals have been optimized using density functional theory for comparison with the isoelectronic tetramethylcyclopentadienyl derivatives (Me 4 C 5 H) 2 M. Low-energy sandwich structures having parallel B 2 N 2 C rings in a trans orientation are found for all seven metals. The 1,2-diaza-3,5-diborolyl ligand appears to be a weaker field ligand than the isoelectronic cyclopentadienyl ligand as indicated by higher spin ground states for some (η 5 -Me 4 B 2 N 2 CH) 2 M sandwich compounds relative to the corresponding metallocenes (η 5 -Me 4 C 5 H) 2 M. Thus (η 5 -Me 4 B 2 N 2 CH) 2 Cr has a quintet ground state in contrast to the triplet ground state of (η 5 -Me 4 C 5 H) 2 Cr. Similarly, the sextet ground state of (η 5 -Me 4 B 2 N 2 CH) 2 Mn lies ∼18 kcal mol −1 below the quartet state in contrast to the doublet ground state of the isoelectronic (Me 4 C 5 H) 2 Mn. These sandwich compounds are potentially accessible by reaction of 1,2-diaza-3,5-diborolide anions with metal halides analogous to the synthesis of [η 5 -(CH 2 ) 3 N 2 (BPh) 2 CMe] 2 Fe. 

Density functional theory studies show that the lowest energy C 4 F 8 Fe(CO) 4 structure is not the very stable experimentally known ferracyclopentane isomer (CF 2 CF 2 CF 2 CF 2 )Fe(CO) 4 obtained from Fe(CO) 12 and tetrafluoroethylene. Instead isomeric (perfluoroolefin)Fe(CO) 4 structures derived from perfluoro-2-butene, perfluoro-1-butene, and perfluoro-2-methylpropene are significantly lower energy structures by up to ∼17 kcal mol −1 . However, the activation energies for the required fluorine shifts from one carbon to an adjacent carbon atom to form these (perfluoroolefin)Fe(CO) 4 complexes from tetrafluoroethylene are very high ( e.g. , ∼70 kcal mol −1 ). Therefore the ferracyclopentane isomer (CF 2 CF 2 CF 2 CF 2 )Fe(CO) 4 , which does not require a fluorine shift to form from Fe 3 (CO) 12 and tetrafluoroethylene, is the kinetically favored product. The lowest energy structures of the binuclear (C 4 F 8 ) 2 Fe 2 (CO) n ( n = 7, 6) derivatives have bridging perfluorocarbene ligands and terminal perfluoroolefin ligands.